Full Project – CONSTRUCTION OF ALUMINUM WALL RACK

Full Project – CONSTRUCTION OF ALUMINUM WALL RACK

Click here to Get this Complete Project Chapter 1-5

ABSTRACT

This project was constructed with the desired materials of construction. The materials include aluminum, glass and wood.  Aluminum was used in forming the skeleton of the structure, glass was used for the doors while wood was used in the sides, top, base and partitions.

After building the skeleton of the structure with aluminum, other materials were used and made up the complete structure.  Materials like glass and wood.

Among the different types of glass available, the thick glass was used due to the fact that it offers greater resistance to hit than some thin glasses through the resistances is not much and can be broken by a fore more than fifty Newton – 50N.  The glass was cut into the measured dimensions by the equipment called “diamond”.  The diamond divides the glass perfectly according to the marker.

The wood used in the construction was cut with the aid of a saw and the edges smoothed with a file.  Both the wood and glass were held firm in the aluminum rail with the aid of a projected rubber.  The aluminum profiles were cut with the aid of an electrically powered machine cutter though manual cutters are available but electrical cutter reduces efforts.

TABLE OF CONTENTS

CHAPTER ONE

Introduction

CHAPTER TWO

2.0     Literature Review

2.1     Types Of Racks

2.1.1  Wall/Mini Racks

2.1.2  Industries Racks

2.2     Rack Protection

2.2.1  Fire Protection

2.3    Materials Of Construction

2.3.1  Aluminum

2.3.2  Bronzes

2.3.3  Wood

2.3.4  Glass

CHAPTER THREE

3.0      Constructional Procedure

3.1      Marking Out/Measurement

3.2      Cutting Operations

3.3      Filing Operations

3.4     Drilling Operations

3.5     Milling Operations

3.6     Coupling And Nailing

3.7    The Instruments

3.7.1  The Milling Machines

3.7.2  The Drilling Machines

3.7.3  The Tape

3.7.4  The Saw

3.7.5  The Diamond

3.8     Working Diagrams

3.9     Parts Of The Rack

CHAPTER FOUR

4.1     Discussion

4.2     Conclusion

4.3    Recommendation

References

CHAPTER ONE

INTRODUCTION

Racks are storage systems used in industries, homes, institutions etc.

Rock of interest of this project is the type of rack found in homes and some other institution.  This is a minim rack or wall rack as it is normally called.  This rack is hung on walls and partitioned within small ranges where material of small size can be kept.

Industries steel storage racks as they are known today did not exist 35 y ears ago.  Rail road cars filled with material in cardboard cartons were hand unloaded into four wheeled platform tracks that were pushed to the elevator of a multistioned ware house and the cartons hand unloaded into stacks on floors with 10 metres high ceilings.  People used the same various trucks to assemble orders from the various  stacks pushing the loaded truck to the elevator and then to the shipping dock where they were unloaded into vehicles for store delivery.  Such rudimentary distribution has been radically changed by some relatively simple innovations.

Forklift trucks have replaced man powered vehicles and loading methods.  They have been on the materials handling stage since the early 1900s and received their biggest impetus during World War II when forklifts were the logistical workhorses of the army and navy.

Unit loads of 2000 – 400016 that are easily picked up and transported by forklift trucks make highway trailer loading and unloading matter of minutes compared to the many hours for the hand unload method.

Industrial ware house buildings with one story ceiling heights of 30ft and wide column bay spalings replaced the multi stored ware houses and are ideally suited for use with the unit load and forklift concept.

Industrial steel storage racks proved to be the fourth necessary materials handling device to maximize the efficiency of the previous three because of “selectivity” and carton crish out.  If one unit load is tried on top of another up to 30ft ceiling height, the bottom load cannot be shipped unless the top ones are removed.

Computer technology has recently been added to all the foregoing to optimize the use and operation.  Today’s modern computes tell the distribution manager when to store the incoming unit loads, when and where to move to the picking face, the sequence in which to pick, and what and when to record. All these component together have provided an efficient system that distributes the food, shelter and clothing of our oriented society.

 

Get the Complete Project

This is a premium project material and the complete research project plus questionnaires and references can be gotten at an affordable rate of N3,000 for Nigerian clients and $8 for International clients.

Click here to Get this Complete Project Chapter 1-5

 

 

 

 

You can also check other Research Project here:

  1. Accounting Research Project
  2. Adult Education
  3. Agricultural Science
  4. Banking & Finance
  5. Biblical Theology & CRS
  6. Biblical Theology and CRS
  7. Biology Education
  8. Business Administration
  9. Computer Engineering Project
  10. Computer Science 2
  11. Criminology Research Project
  12. Early Childhood Education
  13. Economic Education
  14. Education Research Project
  15. Educational Administration and Planning Research Project
  16. English
  17. English Education
  18. Entrepreneurship
  19. Environmental Sciences Research Project
  20. Guidance and Counselling Research Project
  21. History Education
  22. Human Kinetics and Health Education
  23. Management
  24. Maritime and Transportation
  25. Marketing
  26. Marketing Research Project 2
  27. Mass Communication
  28. Mathematics Education
  29. Medical Biochemistry Project
  30. Organizational Behaviour

32    Other Projects pdf doc

  1. Political Science
  2. Psychology
  3. Public Administration
  4. Public Health Research Project
  5. More Research Project
  6. Transportation Management
  7. Nursing

Education

 

Full Project – CONSTRUCTION OF ALUMINUM WALL RACK