Full Project – REFURBISHING OF A FIXED AND FLUIDIZED BED PRODUCTION OF PLASTIC MATERIALS

Full Project – REFURBISHING OF A FIXED AND FLUIDIZED BED PRODUCTION OF PLASTIC MATERIALS

 

Click here to Get this Complete Project Chapter 1-5

ABSTRACT

The repair of the fixed bed adsorption column, a product of arm field technical company was carried out for the purpose of bringing the faulty equipment back to its normal operating system.

Before this exercise, the equipment was out of operation because of the completely blocked base of the fixed bed column (water column) and the malfunctioning of the air control value.

The sintered bronze plate which formed the base of the water column was cleaned up and freed from debris which originally blocked the porosity of the plate to an unacceptably level.  To do this, the plate was soaked in a diluted acetic acid and a current of air used to free the tiny openings from blockage.  Later, the air control valve where properly reactivated, rectified and recalibrated.

At the end the operation of the equipment came back to normal functioning.  The entire equipment was cleaned up and lubricated.

The fluidized bed was run and found to be in good order.

TABLE OF CONTENT

1.0       CHAPTER ONE      – INTRODUCTION

2.0       CHAPTER TWO     – LITERATURE REVIEW

2.1              Absorption

2.2              Types of Absorption

2.2.1        Physical Absorption

2.2.2        Chemical Absorption

2.3              Absorbents

2.4              Desorption

2.4.1        Desorption Methods

2.5              Desorption Operation

2.5.1        Stagewise Operation

2.5.2        Continuous Contact

2.6              Analysis of Fixed – Bed Adsorption

2.7              Adsorption of Solute from Dilute Solution

2.8              The Process of Welding

2.8.1        Oxy-Acetylene Welding

CHAPTER THREE

3.0       REFURBISHING PROCEDURE

CHAPTER FOUR   

4.0       OPERATION OF THE EQUIPMENT

CHAPTER FIVE

Conclusion

CHAPTER SIX

6.0       Recommendation

CHAPTER ONE

1.0              INTRODUCTION

Adsorption is a process in which a substance becomes attached to the surface of a solid or liquid.  The substances adsorbed at a solid or liquid.  The substances adsorbed at a solid surface may be gases, liquids or other solids (from solution).  The amount of material adsorbed by a given mass of adsorbent when the solid is porous of finely divided is large.  This confirms the theory that adsorption is a surface phenomena, since the surface area exposed is much greater when the particles are smaller.

The adsorption operations exploit the ability of certain solids preferentially to concentrate specific substances from solution into their surface.  In this manner, the components of either gaseous or solid solutions can be separated from each order.

In the field of gaseous separation, adsorption is used to dehumidify air and other gases, to remove objectionable odours and impurities from industrial gases such as carbon dioxide to recover valuable solvents vapours from dilute mixture with air and other gases, and to fractionate mixtures of hydrocarbon gases containing such substances as methane, ethylene, ethane, propylene and propane.

Adsorption from liquid phase is used to remove moisture dissolved in gasoline, decolourisation of petroleum products and aqueous sugar solutions, removal of objectionable teste and odour from water, and the fractionation of mixtures of aromatic and paraffinic hydrocarbons.

1.1       Our main objective in this project is to refurbish fixed bed adsorption column.  The scale of operation ranges from the use of a few grams of adsorbent in the laboratory to industrial plants with an adsorbent inventory.

These operations are all similar in that the mixture to be separated is brought into contact with another insoluble phase, the adsorbent solid, and the unequal distribution of the original constituents between the adsorbed phase on the solid surface and the bulk of the fluid then permits a separation to be made.  All the techniques previously found valuable in the contact of insoluble fluids are useful in adsorption.  Thus, we have batch wise single – stage and continuous multistage separations and separations analogous to counter current absorption and stripping in the field of gas – liquid contact and to rectification and extraction with the use of reflux.  In addition, the rigidity and immobility of a bed of solid adsorbent particles make possible useful application of semiconscious methods which are not at all practicable when two fluids are contacted.

Get the Complete Project

This is a premium project material and the complete research project plus questionnaires and references can be gotten at an affordable rate of N3,000 for Nigerian clients and $8 for International clients.

Click here to Get this Complete Project Chapter 1-5

 

 

 

 

You can also check other Research Project here:

  1. Accounting Research Project
  2. Adult Education
  3. Agricultural Science
  4. Banking & Finance
  5. Biblical Theology & CRS
  6. Biblical Theology and CRS
  7. Biology Education
  8. Business Administration
  9. Computer Engineering Project
  10. Computer Science 2
  11. Criminology Research Project
  12. Early Childhood Education
  13. Economic Education
  14. Education Research Project
  15. Educational Administration and Planning Research Project
  16. English
  17. English Education
  18. Entrepreneurship
  19. Environmental Sciences Research Project
  20. Guidance and Counselling Research Project
  21. History Education
  22. Human Kinetics and Health Education
  23. Management
  24. Maritime and Transportation
  25. Marketing
  26. Marketing Research Project 2
  27. Mass Communication
  28. Mathematics Education
  29. Medical Biochemistry Project
  30. Organizational Behaviour

32    Other Projects pdf doc

  1. Political Science
  2. Psychology
  3. Public Administration
  4. Public Health Research Project
  5. More Research Project
  6. Transportation Management
  7. Nursing

Education

Full Project – REFURBISHING OF A FIXED AND FLUIDIZED BED PRODUCTION OF PLASTIC MATERIALS